Although they’re called safety eyes, they’re not guaranteed, and can very occasionally work themselves back out! So do keep a watchful eye on little ones with any toys with eyes. There will be a slight gap between the fabric and the washer because of the little pokeys.Īnd you’re done! Your little guy is ready to be stuffed and all stitched up. If you look at the picture, that is what it looks like all the way down. It usually goes one click past what you think it should. This cannot be undone, as that is the purpose of a safety eye, so make sure you’re definitely where you want to be (even though you’ll be stuck with a hole in your fabric if you go back now!) These can be tricky to push down, so I usually stick my left thumb underneath the eyeball against the right side of the fabric, and use my other thumb to push the washer down. They will help secure the eye to the fabric and keep it from slipping. You want these facing DOWN when you stick it on the eyeball rod, as pictured. You should notice that one side has a few (usually 4) little sharp pokeys. If, even when you stretch at the hole, it is still too small, a few snips at this step can help you along. We are looking at the wrong side of the fabric in this picture, so of course the actual eyeball is on the good side of the fabric. Cutting an actual circle will compromise the structural integrity of the fabric. If your fabric is not stretchy at all, I recommend cutting an “X” shape – just two snips crossing each other. If your fabric is very stretchy, the hole can be tiny and it will work fine. The smaller the eyes you are using, the smaller the hole you need. See how small it is? And this will do just fine. In this example I am using super stretchy lycra, so I only need to snip one or two threads before my hole is big enough for the eye to slip through. REMEMBER: You can always make a hole bigger but making it smaller is much more difficult! Make sure you’re only cutting through one layer of fabric, and just snip one or two threads around the pin. This part was hard to take a picture of because it requires two hands to execute, but this should give you the idea. Make sure the pin stays in both sides, but pull at the fabric a bit so that the two sides aren’t touching each other when we start cutting holes, we don’t want holes in the other side! Check to make sure the pin is coming out the other side symmetrically to your first hole. Here you can see that the pin is going through both layers of fabric. Once you’ve got a fold, decide where the best spot for an eye will be, and stick your pin straight through both pieces. Our goal here is symmetry we don’t want our little guy to end up with lopsided eyes. If you don’t have a seam, fold it at the center. If there is a seam between where you want your eyeholes to be, fold it on the seam (as shown). These are the tools you need: small, sharp scissors (the pointier, the better!), a pin, your safety eye (two pieces: eye and washer), and your unstuffed plush.įirst, lay your plush so it is completely flat. They are quite easy to use, but it can be a bit confusing, so here’s a tutorial to help you install plastic safety eyes on your plush! These eyes are installed before stuffing, and the two-part mechanism prevents the eyes from falling off**. A selection of fine-toothed saws may be available for purchase at hobby stores, since they’re commonly used to cut plastic models and die-cast figurines.Plastic Animal Eyes for Stuffed Animals and Amigurumi now for sale in the Fluffyland shop! Animal eyes in multiple colors and sizes, including assortments!įor many stuffed animals and plush, a simple way to add character and cuteness is to use plastic safety eyes.Some of these fine-toothed saws look like a knife or straight-razor and can easily be used with one hand. Home Improvement Specialist Expert Interview. While all saws will be able to cut through plastic, saws with large teeth will leave the plastic torn or shredded.Using a saw with fine, small teeth will allow you to cut through thick plastic precisely and without destroying the plastic itself. Saw using the full length of the blade, and move the saw in smooth, quick back-and-forth motions through the material you’re cutting. When using a fine-toothed saw, clamp the plastic you’re cutting to a table or work bench with a C-clamp. Cut through plastic with a fine-toothed saw.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |